i have problem with 2009 buell

[rkadlcek]

Hi guys I have a 2009 Buell XB 12 and I have a problem with the exhaust .. I bought a race .. EMC trouble staying .. I can not get any program for EMC 2009 Buell and unable to determine which tuning to fit the teachings of my race EMC ... Please advice where can I get the program for 2009 Buell tailpipe or who sits on my race ...... EMC still note - if you disconnect the lambda sensor flashing light engine but the problem is corrected can affect the life of the engine??

[burgurboy]

You find find almost all race maps at buellmods.com just log in using your credentials for this forum, then go to the downloads section.

Did you say you bought a race ECM? in that case, it should have a sufficient map for your mods.

If it's not running right, wont idle, ect. You need to do a proper tps reset.

Also. Look into the program called ECM spy (im not sure if it works on +08 models). This will allow you to "shut off" your lambda (02) sensor without trouble codes.

you do not need the lambda sensor attached IF *and ONLY IF* you have a good map flashed to your bike. if you are at all unsure about the tuning of your bike, leave the lambda sensor alone.

[Stevenc150]

Please keep it in one thread. No need to post same exact thread in different Topics. It'll be seen on the Home page. ;)[up]

[RuiP]

Wasn't even aware a race ecm was available for 2009. Any idea how much?

[Stevenc150]

It's the EBR pre-programmed OR user-programmable ECM. Check it out: EBR ECMs (http://www.erikbuellracing.com/store/parts-accessories/fuel-injection.html)

[RuiP]

They dont allow you to buy just the race ecm, that blows.

[theoctopus]

To buy just the Race ECM is $305.

For just a bit more than that, I can get you set up with a fully custom map, built around your bike, your riding style, and your environment. I'll also teach you how to do it while we customize everything.

[brightbuell]

p

[unionthug]

Program? You mean map? The race ecm should come with a standard race map and be compatible with a race exhaust. EBR does an ECM mapped for several (specific) exhausts and that is a wonderful thing to squeeze every last 1/10th out of your bike if that is what you really want (provided he does one for your pipe).

Are you looking for an app or program to reset your throttle position? There isn't one. For 2008 and later Buell twins TPS reset is built-in and very simple.


Buell TPS Reset/Rezero Procedure for 2008 & later Buell XBikes and 1125R/CR motorcycles:

The Buell TPS reset for 2008, 2009, or 2010 Buell twins is simple but requires that you perform the following procedure, step-by-step, exactly as described:

0. Begin with the the ignition off, key out, and the run/stop switch in the "stop/off" position.

1. Switch the Run/Stop switch to the "Run" position.

2. Insert ingition key and turn it to the "on" position. Do not start or turn over the engine.

3. Rotate the throttle grip from the closed throttle position to the wide open throttle position hold for one second then rotate back to closed position and hold for one second. Repeat that exact throttle action two more times (three total open/hold-closed/hold cycles) holding the throttle grip gently against each stop for one full second.

4. Cycle the key off and back on.

You've just completed a TPS reset for your 2008 or later Buell motorcycle. Start your bike and ride.

[08ulysessxb12xt]

following ebr's tps reset instructions it doesn't say have the run/stop switch off and key out. it just says.

1. Turn the key on and make sure kill switch is in the run position. leave this way until step 6.
2. Do not start the bike.
3. Turn throttle to full open and hold about one second.
4. Release throttle completely so it snaps shut. wait one second.
5. repeat the steps 3 and 4 two more times.
6. turn the key off for at least 2 seconds
7. Then you can turn on and start.

So basically my question is, does the whole kill switch in off and key out make a difference vs starting the procedure with key off and switch on? and at then at end of procedure do you end it with the kill switch to off for 2 seconds and back on, or with key? I have tried both and no luck in it running right with me ebr pre-programmed > :(