• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

Crankcase breather mod Buell XB12r

Buellxb Forum

Help Support Buellxb Forum:

theslaughter

Member
Joined
Mar 15, 2008
Messages
8
1504_20111112064014_L.jpg
1504_20111112064052_L.jpg
 
had that same setup, but just to let you know it will drain into the filter, you need to have the catchcan before breather. although you will see some accumulation in the catchcan either way, the majority drained into my filter so then i triend a different setup and everythign is good now [up]
 
looks nice that looks like an fuel filter for a non fuel injected Engine it will work . Might want to put a short piece of hose on the end so you can direct the yuck out of the exhaust area. If you extend the filter back a small amount and turn it up-right OR even at a 45deg. angle it will help for keeping the filter clean as well. IF the Glass Filter housing ever Breaks try and use one of Those Clear Small(harbor freight) Plastic AIR Compressor filters it will bolt right in possibly with the same 1/4 in. fittings. Still looks nice and clean.Good picts., too!*Jimi[up]
 
i have the race kit ecm and exhaust should i do this mod wil it do anything for me
 
If you have lower RPM coughing and stuttering, it may - for most it does. It simply reroutes the blow-by gases from exiting into your airbox (intake) to a location of your choosing. That way you know for sure the intake is sucking clean air. Only reason it's on there is because it's an EPA engine mandate.

So it can't hurt anything and only carries the very good chance of helping. (Some do it to keep their inner airbox from getting oil misted all in it. But if you have that problem, it's a sign your engine needs attention, not a reason to do a reroute.)

Either way, it is by no means a performance mod if that's what you were looking for, simply undoes the EPA setup.
 
(Some do it to keep their inner airbox from getting oil misted all in it. But if you have that problem, it's a sign your engine needs attention, not a reason to do a reroute.)

im running into this, what attention does she need?
 
where do i get the red cone shaped filter and can i go with a bigger size does it matter
 
You can get the filter at an auto parts store. Just look for a breather filter. I went with the stainless steel mesh breather filter.
 
ok what about the catch can weres the best place for that and what is the best to use \
 
im going to get the same filter but in red and im lookin to find a catch can i like ,, im in rebuild process and mods are a + heres what i got done so far , plastics and fairings in paint shop gettn candy painted and the parts::: gold axle sliders , gold levers , 10k hid lights, red halo lights ,,new front pads,, hideaway liceance plate or flip plate,, new rider pegs,, smoke double bubble ,, ams oil and wax
8233_20120121142947_L.jpg
 
Txgold....... Be careful with that DZb screen. If left in direct sunlight they have been know to act like a magnifying glass and melt instrument clusters. I had one and it started to melt mine when I caught it....... Soon after the DB was history.
 
At least when you have your headlights on at night they will look like this...

BL-18-ON-S.jpg


:p
 
I had to repaint and bondo the cluster it allready was melted a small whole so its gettin candy red paint too , and the 10k hid lights look white maby a hint of blue not even close to. 12k or higher. Color not purple fool:D
 
Back
Top