Fender eliminator?

[paulr]

What are my options[confused] for the eliminator kits? I'm getn a stainless d&d slip-on, barend mirrors, K&N filter, have it tuned, and the eliminator kit. I bought this new bike while I was stil payn on my lightning so I'm goin all out with this one. I want this bike to look really nice. Thanks all.

[dave_xb12r]

I think the jardine fender eliminator kit is the cleanest. http://www.starcycle-usa.com/catalog/46-5001-03.jpg

I've seen ASB's billet fender eliminator. It's very high quality, but it's too damn expensive. The jardine is $100 less than ASBs putting it around $65

[paulr]

Awesome! I thought all kits were a couple hundred plus so $65 bucks is right up my alley. Got a link to any places that have a good business reputation or should I just google it?

[dave_xb12r]

You can buy directly from Jardine, or you can get it on amazon. Click here for amazon link (http://www.amazon.com/JARDINE-FENDER-ELIMINATOR-1125R-46-5001-03/dp/B0022YDLM6)

[browland]

save 60 bucks chop the stock yourself and paint it with spraypaint

[Stevenc150]

Here's a DIY if you're considering: Fender Chop DIY (http://www.buellxb.com/Buell-XB-Forum/Do-It-Yourself-Buell-Mods/rear-fender-elim-write-up-please.).

[paulr]

Thanks for postn so fast guys. Just to make sure, this is for my cr right?

[paulr]

disregard, I didn't read enough.

[millenniumx1]

I liked the Jardine. Think I got mine from A S B, but not positive. Either way it was about $65, clean install, looks great when done. You'll note in the attached picture that I cut away the under-tail plastic to let the white part of the taillight shine onto the plate. Yes, same kit for the CR as what I used on my '09R.

Mike

http://www.youmarketing.net/100_1057_bw.jpg

[Stevenc150]

Just to make sure, this is for my cr right?:o It's Dave's fault, I was following his lead. Actaully the concept of the link I posted still applies. ;)

[03Firebolt9R]

I have the Jardine just like Mikes pictured above and like it alot.

[paulr]

bought it 20 min ago on amazon. thanks fellas. [up]

[RT Performance]

Little late but gr harley has them in stock
not sure they have them on there web page
wish I had an extra firebolt plate frame i would jut build the filler panel

[paulr]

does this kit keep the stock blinkers???

[RT Performance]

yes

[braindead]

Will the Jardine fit the xbs

[AussieBuellRida]

Spewin.. we cant run these in Oz.. cops r all over it. If caught riding with one on, its an automatic defect. Then need to buy a day permit ($40) to ride to the inspection centre, then $120 to have the defect removed... all because they call the rear fender a mud guard... its got a hugger you stupid F@#ks...!!!!![mad]

[paulr]

Is this new fender hard to put on or is there anything specific I need t know. My instructions are faded and I'm gona try and just figure it out.

[paulr]

bump

[gear2078]

Hey Paul, I haven't installed a new tail yet, still trying to design my own. All I can tell you is that I had to pull both seats off and the top plastic off of the tail section to safely unplug two turn signal wires that were too short to get a hold of. Other than that, if you have two hands you can do it.

[AZCRrider]

Has anyone tried the Evotech fender eliminator? It has the integrated license plate LED. I'm still trying to decide myself.

[RT Performance]

I made one i used my bolt plate frame and made a filler out of thick plexi glass. Remounted my turns in the plastic of the bolt tail and making a new bracket for it
I also removed the leg for the third bolt so i have some extra space for storage.
No brain it will not work on a xbs completely different tail sections.