• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

Search results

Buellxb Forum

Help Support Buellxb Forum:

  1. D

    swapping output shaft 5th gear bearing

    Merry Christmas
  2. D

    swapping output shaft 5th gear bearing

    UPDATE: i got the special tools in and removed and reinstalled the nut. the noise is 100% gone. Big thanks to John for offering to lend me the tools needed to complete the job and for his advice.
  3. D

    swapping output shaft 5th gear bearing

    cruising the net i found this: https://www.youtube.com/watch?v=CacfmuSVk2s it sounds similar to my noise and the owner says his nut was loose on the pulley. that might be what it is on my bike since the engine was changed. i did get the old engine from the PO and the pulley is not on it so he...
  4. D

    swapping output shaft 5th gear bearing

    I'll make a tool to hold the sprocket. I may take you up on that, but I have a few other things I need to grab from the local dealer and if they have one in stock I might as well just get it from there. I can't see your avatar for some reason, but no you didn't buy a CR from me, I never...
  5. D

    I see per this thread ...

    I see per this thread : https://www.buellxb.com/forum/showthread.php?49513-swapping-output-shaft-5th-gear-bearing/page2 That you have a pulley locking tool that you'd lend out. If so I'd like to borrow it please.
  6. D

    swapping output shaft 5th gear bearing

    i pulled the seal in the center of the mainshaft to inspect the needle bearing, it looks good and there was fluid up there. i'm really hoping it's the roller bearing. anyone know if i can use a impact gun to remove the nut? i'd leave the belt and tesioner in place, trans in neutral and give it a...
  7. D

    swapping output shaft 5th gear bearing

    Will do. I need to get that pulley off and verify that the bearing is bad. I really hope that is all that it is, this is my noise. (video link wasn't working correct)
  8. D

    swapping output shaft 5th gear bearing

    Looks like I might need to borrow that holder tool, I'll provide deposit.
  9. D

    Exhaust shootout download

    Thanks!
  10. D

    Exhaust shootout download

    Does anyone have a link where I can download the exhaust shootout?
  11. D

    My worst nightmare...

    Awesome!
  12. D

    Garage Sale, lots of parts

    I'm interested in the race muffler if you still have it.
  13. D

    anyone interested in some parts or bikes

    I'm looking for a race muffler
  14. D

    Planning XC trip on my Uly

    I'm surprised no one said fuel pump. On my my 05 xb9sx and my 06 Uly both had fuel pumps that were bad. Other than that just changed the plugs and rear wheel bearings and was good to. Uly had 10,000 miles on it has around 30,000 on it now. I sold my xb9sx to my buddy and he just sold it with...
  15. D

    2008 XB12Ss for sale in Orlando

    If you're interested in a Uly I might be interested in a trade.
  16. D

    Buell of the month sept

    In the smokey mountains.
  17. D

    So Xoptiinside is No More?

    I don't want to speak for him but I'm pretty sure he said he will still be doing some tuning if you ask him to. He's just not promoting it as much as before. At some point I want another tune from him for my stock muffler so I hope its true.
  18. D

    Uly doesn't fit on Dynojet?

    I wonder if all Harley dealers have a standard Dyno they use? My buddy has a Dyno dynamics car Dyno in Miami, about 150 miles away. I'll probably Dyno it there one day.
  19. D

    Uly doesn't fit on Dynojet?

    I took my Uly into the local Harley dealer today to get it dyno'd and she was too short. The rear tire barley made it to the drum and the front of the rear tire was touching the ramp the front tire rolls up onto. Is this a common problem or was it just how they had their Dyno setup...
  20. D

    Meet the New Owner of EBR

    I don't want to see a post like this from anyone else but the new owner. Intro!!!!!! PS: no offense, just looking forward to getting to know about the new owner and his plans for EBR
Back
Top