• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

Search results

Buellxb Forum

Help Support Buellxb Forum:

  1. D

    Lithium battery is great..until it gets cold..arg

    What would be the highest crank amp battery out there for a Buell? Gel etc.. thanks!
  2. D

    08 Buell-does tach sweep while driving...

    This has me on the right track I think. Its something temp related as well. Early am..65f started up and when I did hard R/L turn it would do the sweep thing. Then when starting up at 80f and turning L/R no sweeping. Sounds like a connection-ground issue? thanks!
  3. D

    What type of connector for the 08 speed sensor?

    3-way....? Don't want to buy a complete wiring harness...just need a connector pigtail. Not sure who manufactured these/style?
  4. D

    ECM pins #1 and #33..Analog AFRs..

    Anyone exactly what these are/do?
  5. D

    08 Buell-does tach sweep while driving...

    Well, I thought I had the issue resolved when I found that the WB O2 sensor was not fully tightened. Weird...not problems until I filled up with gas. Was worse than ever sweeping several times within a few minutes while I drove away. Pulled and replaced all the fuses and relays. Hope that does...
  6. D

    08 Buell-does tach sweep while driving...

    Yes, its just like turning off the ignition only more often than not, the engine just stutters briefly, then catches back on. Wish it would throw a code lol. thanks
  7. D

    08 Buell-does tach sweep while driving...

    And sometimes just dies. No fault codes. Seems to be happening more frequently...any ideas what might be going on? Is this symptomatic of something going bad perhaps? thanks!
  8. D

    Speedometer woes...

    Just a quick update-got the speedo working. Apparently it was a wiring issue at the ecu connector. I had previously had a faulty connection in the connector itself so I pulled all the wires out of the connector. Long story short...the 2 R/W wires although they look the same must go back on their...
  9. D

    Speedometer woes...

    You're the bomb me. Once the rain stops, I'll go check things out.
  10. D

    Speedometer woes...

    Code 43....my rigged wiring may be at fault me thinks. There were 2 R/w stripe wires I removed from the ecu connection plug...might have gotten these crossed up. Is there a fuse for the speedo? It does do the full sweep at key on though.
  11. D

    Speedometer woes...

    I think it was 34...speed sensor short?
  12. D

    Speedometer woes...

    Died. CEL comes on after 3-5' of driving. Replaced the speed sensor today. Still dead. It was a HD sensor that was not a direct replacement...came with the wiring harness and connector which I had to remove and connect to the existing wires (3). Any ideas/suggestions greatly appreciated. thanks!
  13. D

    baro sensor enabled eeprom?

    Trying to tackle this once again.. Got the 08 working fine with the baro sensor using ecmspy mono. Trying to do same with the 07, but there are greyed out areas in the 07 settings via mono. The settings options that I can not enable are: "Read sensors continuously" and "Use baro pressure (not...
  14. D

    Anyone familiar with the HD ver of Megalogviewer?

    Had used the older version years ago, but this senior seems to have forgotten some of the initial settings etc. Using ECMDroid to log MSL files and burn the new tables etc in. Using TunerProRT as well. Using a wideband controller/sensor to create the afr data. Getting AFR readings of 114 in the...
  15. D

    baro sensor enabled eeprom?

    Yeah, was able to set it up using the latest ver of ESpy on my 08 and verified it is working by applying either pressure or vacuum to the sensor. But, cant seem to get it up and working on the 07. Have enabled it via ECMDroid, but still a no go. Was hoping to source a complete eeprom for the 07...
  16. D

    baro sensor enabled eeprom?

    Anybody have a baro sensor enabled eeprom for the BUEID (2007 XB12S) firmware?
  17. D

    Tires

    Shinkos
  18. D

    Megalogviewer VE / tuning

    Hey tok-I used the latest version of MLV to remap tables on both my 07 XB12 and stock 08 XB9SX. Used NTK's latest AFRM wideband sensor and controller. Used ECMDroid to log the data using a 7"tablet and ran that data through MLV. Used TunerPro to modify settings and tables. Used ECMSpy to create...
  19. D

    Map question Xb12ss

    File format issue or perhaps ecm firmware mis-match?
  20. D

    ERROR: Failed to fetch ecm type: Cable Problem (RX/TX Shorted?)

    Getting this msg when trying to connect using ESpy with either cable or BT module. Bike starts up fine and runs...but cant "talk" with it. What happened?? update: So I got out this evening and crank up the beast..no CEL and best thing is was able to connect. Your guess is as good as mine as...
Back
Top