ECMDroid

[oneighty]

I have searched for an answer to what some of the ECM Parameters are in ECMDroid and came up empty handed so I am going to make a list and mention how mine is set so we can get a little comparison and discussion going. These settings are from the Race file for a 2003 XB9S

[General Config]

(System)​

Bank Angle Sensor *checked*
Deceleration Fuel Cut *unchecked*
Fuelpump duty cycle *checked*
Idle closed loop *checked*
Idle Fuel & Ign. Adjust. *checked*
Open loop learn *checked*
Enable starter interlock *greyed*
Enable sidestand interlock *greyed*​

(Noise Reduction)​

On Accel. Condition Only *unchecked*
On Accel. and WOT Condition *unchecked*
On WOT Condition Only *unchecked*
Ramp out *checked*
Suppress Accel. Enrichment *unchecked*
Active Intake *greyed*​

(Airbox Pressure Sensor)​

Baro Correction Feature *greyed*
Airbox Pressure Feature *greyed*
Log Avg. Baro & ABP Corr. Data *greyed*
Log MAP Front/Rear Data *greyed*
Read Baro at Key-On *greyed*
Rear Sensor Continuously *greyed*
Skip Key-On Read if Engine runs *greyed*
Speed Correction *greyed*
Use Baro (not MAP) Sensor *greyed*​

(Shifter)​

Shifter Feature *greyed*
Shifter Transition required *greyed*
Shifter Fuel & Spark Cut *greyed*
Shift Light Feature *greyed*
Shift Light Output *greyed*​

[Error Mask]

(Sensors)​

Air Temperature Sensor *checked*
Bank Angle Sensor *checked*
Baro Sensor *greyed*
Battery Voltage *checked*
Camshaft Position *unchecked*
Clutch Switch *greyed*
Crankshaft Position *greyed*
Engine Temp. Sensor *checked*
Fuel Pressure *greyed*
Manifold Pressure *greyed*
Neutral Indicator Switch *greyed*
O2 Sensor (Rear) *checked*
O2 Sensor (Front) *greyed*
Sidestand Switch *greyed*
Throttle Pos. Sensor *checked*
Velocity Sensor *checked*​

(Actuators)​

Exhaust Valve Actuator *unchecked*
Cooling Fan *checked*​

[Limits]

(RPM Limits)​

{Fixed}​

Soft Limit Trigger 7400
Soft Limit Reset 7350
Hard Limit Trigger 7500
Hard Limit Reset 7450
Kill Limit Trigger 7600
Kill Limit Reset 7550​

{Cold Engine}​

Cold Engine Temp (°C) *greyed*
Soft Limit Trigger *greyed*
Soft Limit Reset *greyed*
Hard Limit Trigger *greyed*
Hard Limit Reset *greyed*​

(Temperature Limit)​

{Limits}​

Soft Limit Trigger (°C) 280
Soft Limit Reset (°C) 275
Hard Limit Trigger (°C) 295
Hard Limit Reset (°C) 285
Kill Limit Trigger (°C) 305
Kill Limit Reset (°C) 154
Engine Light Flashing On (°C) 280
Engine Light Flashing Off (°C) 275​

{Conditions}​

Soft Limit Min. Load *greyed*
Hard Limit Min. Load *greyed*
Soft Limit Min. RPM 3500
Hard Limit Min. RPM 4500
Ignore RPM Trigger (°C) 305
Ignore RPM Reset (°C) 304​

(Fan Setup)​

{Key Off}​

Max Duration (min) 30
Min. Batt. Voltg. 10.0V
On Temp (°C) 170
Off Temp (°C) 150
100% Runtime (s) 15
Run Duty Cycle (%) 40%​

{Key On}​

On Temp (°C) 180
Off Temp (°C) 220
Speed-based Fan Control *greyed*​

[AFV Settings]

AFV (Rear) 105.9%
AFV (Front) *greyed*​

[O2 Setup]

(O2 Sensor)​

Rich (V) 0.56V
Midpoint (V) 0.49V
Lean (V) 0.41V
Minimum RPM 600
Min. Load (8bit) 0
Activation Delay (s) 2.0
Deactivation Delay (s) 2.0​

(Closed Loop Configuration)​

Enable Closed Loop *greyed*
Enable Independent Front CL *greyed*
Log Front EGO & Fuel Data *greyed*​

(EGO Correction Settings)​

Max. EGO Corr. (%) 200.0%
Min. EGO Corr. (%) 50.0%
Max. Engine Temp (°C) *greyed*
Min. Engine Temp (°C) *greyed*​

(AFV Settings)​

Maximum AFV (%) 150.0%
Minimum AFV (%) 60.0%
OL Learn Delay (s) 3
Increase Factor (%) 105.3%
Decrease Factor (%) 95.0%
Transitions required 21
Max. Engine Temp (°C) 260
Min. Engine Temp (°C) 120
Max. Cylinder Diff. (%) *greyed*​

[Exhaust Config]

Exhaust valve enabled *greyed*
On in WOT only *greyed*
Keep open when not in WOT *greyed*
Reverse control polarity *greyed*
Reverse feedback polarity *greyed*
Close Valve on AMC error *greyed*
Off when power limited *greyed*
Cycle valve at ignition-on *greyed*​

 

[Cooter]

What ECM perameter are you asking about?

 

[oneighty]

Well I have a post on the Lightning sub forum stating my actual problem. I think my key on fan settings are backwards for one. I'm a little unclear about the error masking and general config settings. As in, what is changed by checking or unchecking them. For example, according to my current settings are potential errors with my O2 sensor being masked?

*In general I wanted a place for everyone to come compare some of their settings and discuss what those settings mean and how they work.