help-ebr race ecm and tps reset

[rchuff]

just got ebr race ecm and need to know where to set tps.should i set it at 4.6 to 5.1 like ecmspy would welcome any help thanks guys.

 

[noone1569]

If you are trying to use ECMSpy to reset your TPS with an EBR ECM, you will trash the ECM.


http://www.buellxb.com/Buell-XB-For...roubleshooting/ECMspy-corrupted-New-Race-Ecm-

 

[Blastonia]

So how can you tell if the ebr ecm is an older ecmspy compatable one or a newer non one?

 

[noone1569]

According to EBR's ECM Programmer, none of the EBR ECMS should be used with ECMSpy.

 

[xoptimizedrsx]

You will NOT trash the ecm done correctly. That is a myth...

Those whom trashed the ECM did it by user error...
Stone cold fact... Never use ecmspy on 2008 up bikes... NEVER.... Even if the fuel cells are in order dont use it on 2008 up bikes

2008 up firmwares dont need a tool and if you did use one you did the damage yourself from low education on the user manual from the bike.

2007 down bikes are fine and firmware dependent...
Safe firmware versions are.
BUEGC Tubeframe, 1999-2002
BUEJA Tubeframe, 1999-2002
BUEKA Tubeframe, 1999-2002
BUECB XB9, 2002-2003
BUEGB XB9 & XB12, 2004
BUEIB XB9 & XB12, 2005-2007
BUEIC XB9 & XB12, 2005-2007 (Japan)

ANY OTHER FIRMWARE DO NOT USE IT NO MATTER WHAT YEAR...

Just use this NEW tool it uses the code that tells the ecm to run a reset sequence. which is the ecm code itself.

The new Tunerpro RT ADX filke in live data. It is completely different in protocol than ecmspys data. 100% correct.

Posted at Xoptiinside.com the ddfi2 ADX is the one you want.

You will see the ddfi3 adx as well which does not have a TPS reset in it because it is controlled by key switch and throttle movements...


Those are Facts... I don't care what horses mouth says what on it... Some people are very ticked the full ecm details got figured out and all the data got put into the best software on the market to do anything in the ecm for free...

 

[noone1569]

You will NOT trash the ecm done correctly. That is a myth...

Those whom trashed the ECM did it by user error...
Stone cold fact... Never use ecmspy on 2008 up bikes... NEVER.... Even if the fuel cells are in order dont use it on 2008 up bikes

2008 up firmwares dont need a tool and if you did use one you did the damage yourself from low education on the user manual from the bike.

2007 down bikes are fine and firmware dependent...
Safe firmware versions are.
BUEGC Tubeframe, 1999-2002
BUEJA Tubeframe, 1999-2002
BUEKA Tubeframe, 1999-2002
BUECB XB9, 2002-2003
BUEGB XB9 & XB12, 2004
BUEIB XB9 & XB12, 2005-2007
BUEIC XB9 & XB12, 2005-2007 (Japan)

ANY OTHER FIRMWARE DO NOT USE IT NO MATTER WHAT YEAR...

Just use this NEW tool it uses the code that tells the ecm to run a reset sequence. which is the ecm code itself.

The new Tunerpro RT ADX filke in live data. It is completely different in protocol than ecmspys data. 100% correct.

Posted at Xoptiinside.com the ddfi2 ADX is the one you want.

You will see the ddfi3 adx as well which does not have a TPS reset in it because it is controlled by key switch and throttle movements...


Those are Facts... I don't care what horses mouth says what on it... Some people are very ticked the full ecm details got figured out and all the data got put into the best software on the market to do anything in the ecm for free...

I know you're the "Tuning GOD" on here, but emperical evidence proves you incorrect in this instance.

2005 XB12R here, EBR ECM installed. Connected ECMSpy to reset TPS with EBR ECM, and the bike began to run erratically. EBR ECM returned to EBR for analysis and analysis by their programmer, Danny Bilansky returned that ECMSpy corrupted certain cells in the program which caused the motorcycle to run erratically.

Thus, EBR now warns that one should not use ECMSpy with an EBR ECM.

I am not sure why you are implying that firmware was intentionally altered by a user when merely trying to reset TPS.

I understand you are trying to sell a product. Misleading people, accusing them of ignorance, and negative talk of EBR is certainly not the best way to do so. Best of luck on your sales, sir.

I am merely trying to warn others in order to prevent damaging their good they purchased from the "horses mouth" while trying to support the good company that brought us all to Buell to begin with.

 

[rchuff]

thank for the info guys