Axle and wheel bearings becoming one

Buellxb Forum

Help Support Buellxb Forum:

0

03Firebolt9R

Well-known member
Joined
Jan 19, 2009
Messages
1,321
Has anyone experienced the axle and wheel bearings seizing up together? If so, any suggestions...Here is my problem. When trying to remove the front wheel, the axle is loose but when it is turned the wheel/wheel bearings move with it and actually pushes the forks apart instead of threading out. Have tried to hammer with rubber mallet but nothing. I am afraid to get too agressive with it in fear that it may strip the threads.
 
Spray both sides of the axle at the bearings with a good penetrating lube and let it sit for a few hours, then give it a try.
 
To answer your first question, I have not read anything one here or heard of the bearings seizing to the axle but as a rule of thumb for myself I always add a small amount of all purpose grease to the inside lip of the bearings before reassembling.
 
Yeah, I am going to do that for sure. This is the first time I have tried to take the wheels off, the previous owner says he anti-seized the crap out of them last time he did it, but I need to get them off first. [mad]
 
This happened to me too! Luckily the forks weren't damaged!:D

I used a rubber mallet to lightly tap the forks hence pushing the axle through the bearings, then lightly lubed it during reassembly.
 
BIGGER HAMMER! And swing like you mean it!

And lubricant usually makes just about everything easier. A good rust-buster type penetrating lube would do wonders.
 
BPG [up] for using "penetrating lube" in a sentence.

I am not the only one with a juvenile sense of humor am I?
 
50dro...Thanks, I tried this yesterday and again today. I have hit the forks pretty hard, I am concerned about stripping out the threads on the forks/axle.

I bet BPG is used to using "penetrating lube" all the time seeing how he works for HD service. Last time I was in there I left feeling raped.:)

I too have that sense of humor Macbuell.[up]
 
Harley hays great penetrating lube!

Every time I leave the dealership i never feel neglected, abused but never neglected.
 
03Firebolt9R...I'm not sure if you're doing this exactly the way I did or not so I'll clarify a bit...

1) You want to loosen the axle JUST until it starts to bind a bit (not too much so that you start to bend the forks or compromise the fork seals).

2) Give the brake side of the forks a swift "smack" with the rubber mallet.

3) If it only loosens a bit, repeat steps 1 & 2 until it breaks free. Those threads are pretty beefy. I personally doubt that you would be able to strip them by hitting the fork with a Rubber mallet???? Just make sure you have a few threads engaged when you do so.

4) If it's still stuck beyond where the threads engage, you'll need to use something small to lightly tap the axle out (I've used a 3/8" socket extension for this in the past). Be careful not to damage anything if you have to perform this step.

Oh....and "penetrating lube" can be your best friend!!(That's what she said):) Just be careful not to get it on your brakes or tire for obvious reasons[smirk]

I hope this helps you...Good luck!!
 
Thanks for the help guys...went to Oreilly's the other day and got some lube called Freeze Off. Sprayed it on there, let it sit a few minutes and whacked it as I had before but this time it broke loose. So all is good and I got the new Bridgestone Battlax's on and they are great.
 

Similar threads

L
Service Record
Replies
7
Views
8K
Lakota
L
T
  • Locked
Need fuel for a debate
Replies
13
Views
5K
njloco
N
M
2004 Buell XB12R No Start Condition
Replies
2
Views
714
njloco
N
C
Swing-arm sprung, axle will not grab threads
Replies
17
Views
7K
Camp762
C
TapRoot
Second Fuel Pump within 7K miles & 2nd Season ?
Replies
5
Views
2K
Barrett
Barrett

Latest posts

Back
Top