• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

Search results

Buellxb Forum

Help Support Buellxb Forum:

  1. munkiep

    ignition coil secondary winding out of spec?

    i THINK i may have at one point flashed a bad map (or wrong one altogether). i had 5 different xpr files on my phone, some were for editing, others for flashing. of course the temperature has been much lower than what it was when it would act up, but i recently hooked up my laptop with a cable...
  2. munkiep

    Who uses ECM Droid (app)?

    after reading what cooter said about voltage, i believe that to be the problem, i recall voltage dropping below 10.5 volts on cranking, so its probably not retaining a stable connection with the dongle. ill try the jump box approach next
  3. munkiep

    Who uses ECM Droid (app)?

    have you been able to successfully log a .msl file?
  4. munkiep

    ignition coil secondary winding out of spec?

    i would have tried that with the old wires, but i threw them away long ago. At this point im leaning toward the CPS or ECM, as the problem only surfaces after the bike warms up (goes into closed loop?). Its frustrating since its not throwing any codes at all now. Think i may take the ecm out...
  5. munkiep

    ignition coil secondary winding out of spec?

    I remembered I would have a slow starting condition if i didnt keep the bike on a trickle charge, so i tested voltage drop at startup the other day, it dropped from 12.8 to 10.5 volts, but still started (this was right after being on a float charger for several days). ive also left it off the...
  6. munkiep

    ignition coil secondary winding out of spec?

    oh, and i got the codes that were stored when all of this started, code 23, 15 and 32, all of them say "short to ground"
  7. munkiep

    ignition coil secondary winding out of spec?

    starts up, but low idle, tps set to 5.8 degrees, then it will surge up to 1150-1200 rpm, then back down (and sounds like it idling on one cylinder when it drops back down), once its reaches operating temp, partial throttle (cruising) it bucks like its missing, exhaust popping alot when i let off...
  8. munkiep

    ignition coil secondary winding out of spec?

    thanks for the reply Cooter, i had the injectors cleaned while everything was apart, the guy that did it said at 49 psi they flowed extremely well and even. ive made sure that the intake box seal is correct every time ive had it apart. i'll recheck the intake seals when i reassemble, i did the...
  9. munkiep

    ignition coil secondary winding out of spec?

    i should add that i started having problems when the bike would warm up at cruising, WOT, and idle. upon changing out intake seals, i found the front plug wire had rubbed against something almost to the core and the boots were terribly cracked. I replaced the wires after finishing seals, and...
  10. munkiep

    ignition coil secondary winding out of spec?

    testing resistance on primary windings shows .5-.6 , even after i warmed it up. however secondary windings (end to end of coil, not pins) shows 13.5k, manual says 5500 to 7500. someone posted a video on youtube showing testing primary windings, but didnt show anything about secondary windings
  11. munkiep

    Fuel injector options

    So I've changed my intake seals and O2 sensor after dealing with high AFV readings. If i flash a race map, the bike wont idle correctly unless the AFV is set to 149. If i flash the stock maps, it wont run correctly unless AFV is 115. Not long ago, i had to trailer the bike home due to a fuel...
  12. munkiep

    Who uses ECM Droid (app)?

    i did this, hence the reason i can view live data until the bike is cranked
  13. munkiep

    Who uses ECM Droid (app)?

    what are your steps for connecting to the bike to view live data while the bike is running? I can't seem to get mine to stay connected once i crank the bike, nor can i get it to re-establish a connection once the bike is running. i can view live data while the bike isnt running (tps, temp, etc)...
  14. munkiep

    Replacing intake gaskets (DIY TUTORIAL)

    i took you guys' advice and went without any sealer. upon pulling my coil and wires out, i believe i found why my bike doesnt want to stay idling when cold and loss of top end power...
  15. munkiep

    Replacing intake gaskets (DIY TUTORIAL)

    wow, i had read and re-read this topic several times several months ago. just tonight i tore all the plastics down and loosened the manifold bolts, then got to a stopping point (those coil bolts are being stubborn), and got on here to read once again, only to see this comedy that had started...
  16. munkiep

    tell me why someone would do this?

    i'm surprised at how many members have been on here for such a long time. it seems as though i have finally found a motorcycle that's as much fun as it is reliable. and BTW, i was unable to get a picture of the incorrect pulley on the bike, i was so focused on getting it back on the road that...
  17. munkiep

    tell me why someone would do this?

    i know Squid has an image comparing the two on the link he posted, here are a couple more comparisons for anyone in the future (2003 being the shorter one). when i get everything back together this weekend, i may take a picture of what the incorrect idler arm looks like on the bike (if it will...
  18. munkiep

    tell me why someone would do this?

    thanks squid, i was wondering about the master cylinder swap being necessary. i'll let you know on that bracket, so far i know i have one coming for an '05 (so im a step ahead on the 04+ swap, ordered before i knew they are indeed different) and a seller has just accepted my offer for $30 on...
  19. munkiep

    tell me why someone would do this?

    when getting another idler assy., how do i know its the correct one? i only see one on ebay listed for an 03, but the pictures show it has 6203 bearings in it, and from what i can gather, the 03 used a single 5203 bearing. dont tell me im going to have to buy new...
  20. munkiep

    tell me why someone would do this?

    i knew i was leaving something out originally (it's a lightning xb9s). anyways i'll follow up when i get it all back together, nothing irks me more than searching for a problem and finding where someone in the past has had the same problem, but fail to later tell the outcome or solution.
Back
Top