• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

Search results

Buellxb Forum

Help Support Buellxb Forum:

  1. C

    2008 xb12s rear sprocket bolts

    I'll keep the old ones for spares. I received the new bolts for the rear sprocket and they seem to have a gray material on the bolt already. Assume this is some sort of loctite? Do I need to apply anything else to them before install because the manual says to just install and torque. Thanks.
  2. C

    2008 xb12s rear sprocket bolts

    All though the price seems a bit steep for bolts I located the part number in case anyone else needed it. Seems most places are charging 3 bucks a piece. AA0609.11CXZB
  3. C

    2008 xb12s rear sprocket bolts

    Anyone happen to know the official part number for the bolts that hold on the rear sprocket on the rear wheel? I am about to remove the rear sprocket and assume these bolts shouldn't be reused. Thanks fellas.
  4. C

    Engine oil level question

    Am I not allowed to ask questions on a message board because I have been a member for 11 years, 213 posts? My bad....
  5. C

    Engine oil level question

    Am I not allowed to ask questions on a message board..no matter how long I have been a member for?
  6. C

    Engine oil level question

    Thanks fellas
  7. C

    Engine oil level question

    XB12 Engine oil level question So for quite a while now when refilling the engine oil I was going with the process of filling to just where the oil would barely touch the bottom of the dipstick during a cold check. After a ride of about 30 minutes I check the oil as soon as i get off the bike...
  8. C

    Hose near airbox cover 2008xb12scg

    Thanks fellas. I'll have to trace it and see where it goes. Will report back
  9. C

    Hose near airbox cover 2008xb12scg

    Anyone know where this hose is supposed to be routed? Don't see any obvious area where its supposed to be connected. Since I have had the bike i usually just tuck it on bottom side of the airbox. Thanks fellas.
  10. C

    Oil pump cover removal

    Hey everyone, I need to swap out just the outer oil pump cover on my 2008sb12scg which is part number 1 in the diagram. Is there any bad things that would happen with just replacing that part? I know in the manual is states that if removing the pump itself you need to unload the valve train to...
  11. C

    Primary Case Powder Coating Prep

    Hey Everyone, I am going to have my primary case powdercoated with a textured flat black and had a few questions on the prep steps I should give the painter. Where the screws go in to attach the case to the engine there seems to be very small circular areas around the screw holes that don't...
  12. C

    2008 xb12scg rear wheel

    Hello everyone, I need to replace my rear wheel on my 2008 xb12scg and was curious if a rear wheel from a 2006 BUELL ULYSSES XB12X would work. Are the wheels exactly the same looks wise and dimension wise? From some pictures I found they look exactly the same but hard to tell 100%. Thanks.
  13. C

    Bank angle sensor retaining clips

    Hey Guys, I seemed to have lost the retaining clips for my bank angle sensor. Anyone know the part numbers for those or am I just better off using a few zip ties? Thanks.
  14. C

    2007 XB12SCG fuse box clip broken

    Dang....didn't realize it would be that involved. Velcro it is.
  15. C

    2007 XB12SCG fuse box clip broken

    Hey guys, Busted off the clip on the part of the fuse box that is attached to motorcycle itself. I am assuming to fix my blunder I will need to rip the base out and replace? How much of a pain will this be to replace. Do I have to take whole whole tail assembly apart? Thanks fellas.
  16. C

    Leaking clutch cable

    Hey everyone. Have a slow leak in clutch cable on my 2007xb12scg and was wondering if there is any quick fix for this or if I should just replace the whole assembly. The leak is actually coming from between the rubber hose and the metal fitting, not where is screws into the primary cover. Bike...
  17. C

    Brake bleeder valve question

    If I were to completely remove the bleeder valve from the caliper would brake fluid start spilling out? Stupid question...i know, but just curious. I am thinking about installing some speed bleeder valves and didn't want a giant mess on my hands.
  18. C

    2007 XB12Scg belt replacement

    I went with the BDL Falcon SPC Rear Drive Belt------PART # BDL-SPC-128-118 and it fit nicely. As you can see from my post in this thread...everyone inspect your belts occasionally :)
  19. C

    2007 XB12Scg belt replacement

    In terms of visual inspection I would look for similar wear and tear. These pictures were from the belt I just took off my bike.
  20. C

    2007 XB12Scg belt replacement

    Thanks guys! The belt has some damage to it. Has a crack starting to form in the middle of the top side of the belt. Looks like something hit it...maybe a rock.
Back
Top