-
You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
If you have any problems with the registration process or your account login, please contact us.
2007 XB12s has red trouble light on, need help diagnosing it please
- Thread starter Race4k
- Start date
Help Support Buellxb Forum:
Barrett
Well-known member
Procedure and codes after locating diagnostic plug. Plug location shown in your owners manual. Locate plug and while looking at it with pins facing you the locking tab must be in the 12 o'clock position.
Pin 1 -- upper right corner
Pin 2 -- lower right corner
Pin 3 -- lower left corner
Pin 4 -- upper left corner
With the ignition switch off, install a jumper wire across pins 1 and 2 in the diagnostic plug.
Turn the ignition switch to the ON position and wait approximately 8 seconds for the check engine light to start flashing.
All trouble codes are sent out as a series of flashes. To rettrieve the first digit of the code, simply observe the number of times the lamp flashes.
The transmission of a trouble code is always preceeded by six rapid flashes (about 3 per second). This transmission is followed by a 2 second pause in which the lamp is off. The lamp will then flash one or more times to indicate the first digit of the trouble code. The length of time that the lamp will be either on or off when indicating a trouble code is about 1 second in duration.
Following the transmission of the first digit in the trouble code, there will be another two second pause before the second digit is transmitted.
After the second digit is transmitted, there will be another 2 second pause. After the pause comes another intermission (six rapid flashes) after which the next stored code is transmitted in the same manner. Once all the trouble codes have been displayed, the sequence will repeat.
If all you observe is the rapid flashing, then no trouble codes have been stored.
When done, turn the ignition key off and remove the jumper wire.
There is no way to clear trouble codes using this method. The only way to clear codes without hooking the bike up to a computer is to take the bike through 50 start and run cycles (start engine, run for at least 30 seconds, shut it off).
The trouble codes are as follows:
11 Throttle position sensor
13 Oxygen sensor
14 Engine temperature sensor
15 Intake air temperature sensor
16 Battery voltage
21 Interactive muffler control (XB12 only)
23 Front fuel injector
24 Front ignition coil
25 Rear ignition coil
32 Rear fuel injector
33 Fuell pump
35 Tachometer
36 Cooling fan
44 Bank angle sensor
52, 53, 54, 55 ECM failure
56 Cam sync failure
You're welcome.
Pin 1 -- upper right corner
Pin 2 -- lower right corner
Pin 3 -- lower left corner
Pin 4 -- upper left corner
With the ignition switch off, install a jumper wire across pins 1 and 2 in the diagnostic plug.
Turn the ignition switch to the ON position and wait approximately 8 seconds for the check engine light to start flashing.
All trouble codes are sent out as a series of flashes. To rettrieve the first digit of the code, simply observe the number of times the lamp flashes.
The transmission of a trouble code is always preceeded by six rapid flashes (about 3 per second). This transmission is followed by a 2 second pause in which the lamp is off. The lamp will then flash one or more times to indicate the first digit of the trouble code. The length of time that the lamp will be either on or off when indicating a trouble code is about 1 second in duration.
Following the transmission of the first digit in the trouble code, there will be another two second pause before the second digit is transmitted.
After the second digit is transmitted, there will be another 2 second pause. After the pause comes another intermission (six rapid flashes) after which the next stored code is transmitted in the same manner. Once all the trouble codes have been displayed, the sequence will repeat.
If all you observe is the rapid flashing, then no trouble codes have been stored.
When done, turn the ignition key off and remove the jumper wire.
There is no way to clear trouble codes using this method. The only way to clear codes without hooking the bike up to a computer is to take the bike through 50 start and run cycles (start engine, run for at least 30 seconds, shut it off).
The trouble codes are as follows:
11 Throttle position sensor
13 Oxygen sensor
14 Engine temperature sensor
15 Intake air temperature sensor
16 Battery voltage
21 Interactive muffler control (XB12 only)
23 Front fuel injector
24 Front ignition coil
25 Rear ignition coil
32 Rear fuel injector
33 Fuell pump
35 Tachometer
36 Cooling fan
44 Bank angle sensor
52, 53, 54, 55 ECM failure
56 Cam sync failure
You're welcome.
Cooter
Well-known member
Thanks for the awesome and informative post! It's like you've been asked that before:black_eyed:
Barrett
Well-known member
My pleasure Shaughn and yes...a few times. Hope you're recovering well from all those injuries you mentioned on here.
