• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

EBR Exhaust mod

Buellxb Forum

Help Support Buellxb Forum:

Cooter

Well-known member
Joined
Dec 1, 2012
Messages
11,040
Location
Crawling up your skirt
'Race bike' blah blah, but if you need to service ANYTHING besides the clutch-pack on the right side of the motor, you WILL be splitting the bike in 2 for an engine 'rotate'.

Cylinder timing chain, guides, clutch basket (or anything behind it), balancer, water pump, anything. You can't even drain the coolant properly. Why? Because the monster of the rear head pipe covers most of the engine and it's impossible to remove or even get to the header flange nuts without getting the frame out of the way by dropping the engine.

My particular 2014 #000024 has had a series of unfortunate events that made that specific surgery necessary way too many times in a row.

I have had to replace the clutch basket for rattly damping springs, I have had one of the clutch basket to gear bolts shear off at Chuckwalla and leave a hole from it's 11 billionty MPH exit in the inner clutch housing, the 'new' housing had a leak in the rotational seal in water pump, and the .03¢ washer that drains the coolant also has leaked. ALL of which require the bike to be split. Do you know how frustrating a .03¢ washer replacement is, when you have to sacrifice a WHOLE sunny Saturday to do it?! It's a six pack. Thats how frustrating it is, and whats this damn extra bolt go to?!?! I digress.

Ya, I'm pretty fast at it now. But thats not the point.

Front and rear stands on, left side controls off, muffler off, right side fairing off (SX), the ENTIRE intake system out, lower shock bolt off, a-frame ladder and straps to support the tail, scissor jack under the front of the engine, 6 engine mounts, and lower the jack/raise the tail.

And when your table is occupied because you got suckered into another project bike, your knees are gonna hurt. Both of them.
51749898566_76cbfb1ed3_b.jpg


#Buellife
 
Ok ya so... the point.
I need a way to just remove the offending exhaust pipe easily, so I took it off, chopped it in half:)eek:) and then tried to figure how to put it back together.

I chopped it at the straightest part of the pipe past the O2 bung, but before the bend. This would clear the inner clutch cover while still attached to the head. I got some stainless tubing I got to make tips from in the scrap pile that sleeved perfectly on the end of the header, and dammit if it didn't fit the part I cut.

51750147758_c06f39e655_b.jpg


Mandrel bent or not, its a bit smaller at the OE bend. I sliced about .100" out with a band saw and hose clamped into the right diameter. WIN!

Got a pack of 60mm long muffler springs from the China shop along with a pack of stainless hooks. Maybe $10 total with shipping and I feel guilty enough I bought noodles for lunch and tipped well.
 
Last edited:
I took some time to place the hooks where I'd be able to get to them while installed. If you look close, I ended up flattening the inside bend ones a little to get closer to the radius of the pipe, and trimmed the leg off the one that was butting against the O2 bung.

I also made sure to get them about 180* on the circumference and close to level. I used hose clamps to hold the hooks in place and tried the install/un-install to make sure everything was copacetic.

Then I called in a pro:
51749898556_d1e3ec6612_b.jpg


I'd happily heliarc something that gets painted (THICK), powdercoated, hidden under carpet, rhino lined..... :black_eyed: but when it comes to an obvious mod, well in the judgmental view of the critical masses... nope. I'll never be at Bud's level of a lifetime of aerospace technical perfection. It's good to have friends:love_heart:

51750547884_81287fb3f1_b.jpg

It's a beaut' Clark!
 
Eagle eyed readers will see the inner clutch cover is a different color. It's a '09 1125CR part, to temporarily replace the 2010 1125R part, thats replacing the 2014 EBR part:upset: #Buelllife
51750147793_dc462d65a4_b.jpg


Boom shaka laka!

Now when the wizard behind the curtain at Aagard Moto Foundry uses the special effing tool :mad-new: required to replace the rotary shaft seal on my NEW clutch cover, I can swap it out in a matter of minutes versus the a-frame ladder malarky. He's awesome. You should buy stuff.

Speaking of that, for the non fab-olichious... there IS an easier way. I'd recommend getting the 2-piece rear header from APH. Get it from Chaz at Aagard, or NCCR if you're on the mushy peas/warm beer side of the planet.
It's beautiful. Better. And done like an actual professional would do it.
View attachment 15979
 
Back
Top