• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

Update your XB's handlebar controls!

Buellxb Forum

Help Support Buellxb Forum:

Cooter

Well-known member
Joined
Dec 1, 2012
Messages
11,040
Location
Crawling up your skirt
Hello boys and girls! Stinky Whizzleteets here to show you how to update the old, small switches in your handlebar controls to a much more modern look and feel! This was so easy, I would recommend the upgrade even if you simply have a starter button corrosion issue or something.

51102061479_f993c66b0d_b.jpg


Left side:
This was literally plug n' play. I picked up a used left switch assembly from e-bay for a EBR 1190 ($35) and it screwed on and plugged in perfectly.

Right side, you have 2 choices:
1) Use the plug n play EBR run/stop housing. It bolts on and plugs in. But that switch housing does not hold the throttle tube like the stock XB does, so you need to also install the separate EBR throttle housing ($25), and EBR throttle cables ($110) and attach to your XB throttle body. It does work this way, but I prefer the all inclusive/ single housing look for this bike.

2) Use a single housing that matches the switches on the left side but also will house the throttle cables and tube. But where do I get that? Kawasaki. I know for sure the Versys 650 and the Ninja 400 have one that works, but cruising through the dealership, most Kawis that have this single unit housing look the same. I wouldn't be surprised if they all were the same part number but there is one issue:
51101981401_c0eff5687a_b.jpg


It does bolt directly on, the throttle cables are a match and even the throttle tube is the same diameter, but it's not quite plug n play.
51103090120_fc4c71b011_b.jpg

Don't fret! Cooter is here to save you from the evil electron confusion.

You could cut off the Buell switch plug and butt connector to the end of the Kawi harness (instructions are coming) but if you want to do it super clean...

Go to this awesome guys website and spend $8:
http://www.cycleterminal.com/amp-multilock-070.html
to order one of these AMP 070 multilock connectors (part number 174922-2). It comes with enough terminals, but for $3 you should get at least 2 in case you screw something up:eagerness:
and you will also need (2) male spade connectors .110 size. He has 480pc kits with covers for about $5 but they are pretty universal to find in a hardware store.
51101981791_4858093fb9_b.jpg

51102061404_ac8d89117d_b.jpg
 
Last edited:
The Buell switch has 4 terminals. Remove it and unplug it from the harness.
The Kawasaki switch has 6 terminals because the leads for the brake light switch are included and ran cleanly in the single wiring sleeve instead of separately like Buell does. They pop out of the Kawi housing on a short pigtail and have the correct connectors for the Buell switch.
51103090280_fa1c3e5514_b.jpg

You can either leave the brake light wiring completely alone, and ignore the 2 black wires in the Kawi plug...
or go ahead and unplug the 2 stock wires from the stop light switch right under the brake lever pivot, and pull them through into the wiring area behind the windscreen:up:
51102061434_d205d95897_b.jpg

Now you have the open 4 terminal plug and 2 open .110 female spades for the brake light switch. 6 total, just like the Kawi plug. See? I told you this was easy.
Now chop off the green Kawi plug.

You will have:
(2) Black wires, these are for the brake light switch, direction doesn't matter, thats why they are both black, put on the .110 male spades and plug them into the stock Buell female spades you just pulled off the switch.
(2) Black wires with a red stripe. These are for the starter button. Again, the direction doesn't matter so put them in the #1 and #2 spot in the new Buell plug, or butt connector to the red striped Buell wires (Black/Red and White/Red) in the old plug.
(1) red and (1) Yellow/Red stripe left for the Run switch! and you guessed it. Direction doesn't matter here either. Plug them in the remaining holes (#3 and #4) or butt connector to the Grey and White/Black on the Buell plug you chopped off your old switch.
Buell AMP terminals crimped on the Kawi leads:
51102081162_df75c7bba0_b.jpg

See the terminal numbers on the plug, thats where the Kawi wires go:
51102081187_ce4e2ec169_b.jpg

* The female connector on the Buell wire harness side has different colors going into it (A freaking pet PEEVE of mine) so don't look at it, it will only confuse.
Now test your handiwork!
Make sure the run switch is off and turn the ignition on. Check the brake light operation.

WITHOUT turning on the run switch, press the starter button. Nothing should happen. IF you hear the fuel pump prime, you have reversed the (#1 and #2) and the (#3 and #4) wire pairs. Keep those pairs together and switch them in the plug socket to the other side.

If nothing happened when you pressed the starter button, it's ok check your neutral light, turn on the run switch (fuel pump should prime), hit the starter, and wheelie the **** out of your new rad ride.
 
Last edited:
To paraphrase and simplify:
Green Kawi Plug:
black wires to Buell stop switch wire ends
black wires/red stripe to Buell black/red, white/red on Buell plug (switch side)
Red and yellow/red to Buell Grey and White/black on Buell plug (switch side)

You can even just look at where they go inside the Buell housing if you get confused.
51101981431_f6269262d8_b.jpg


And the Kawi one:
51103090310_ba5b84189c_b.jpg

51101981451_e71b711095_b.jpg
 
Last edited:
Nice write up! Added to my list of mods when it gets hot this summer. I've been wanting to do a deep dive on my wiring since the PO appears to have modified somethings with suspect quality, and the controls have always felt cheap to me on this bike...
 
Thanks! It seems trivial, but it totally makes a difference on how you interface with the bike. Especially if you have something newer in the garage that you also ride. The old switches CLICK! Crunch! and the new stuff is a big, cushy, positive lock. They just feel... better.

I used to think the e-bay $30 levers were the same, thinking that (fittment issues aside) its a billet part? what could be so different? But ya, squeeze some CRG's or ASV's and you know right away what the difference is.

Getting on this bike is totally my happy place, why not make it perfect?
 
Not terribly specific, but not 1976. If it look like the one you want (the one in the pic) your GTG. They have used it for many years on many different bikes. I don't know the cut off and it really doesn't matter as long as it looks right (like the pic).:eagerness:
 
Not terribly specific, but not 1976. If it look like the one you want (the one in the pic) your GTG. They have used it for many years on many different bikes. I don't know the cut off and it really doesn't matter as long as it looks right (like the pic).:eagerness:

You really need to do a better write up on this process. It’s like reading some Facebook blathering.
 
Darn it. Really?

It's one of my favorite upgrades because they just feel so classy:cool: I think about it every time I get on one with stock switches and CRUNCH them into place.
 
It is a great mod, and I will likely do it on the methbuell, but you left out details.

It does bolt directly on, the throttle cables are a match and even the throttle tube is the same diameter,

Which throttle cables are a match? Use the Kawi throttle cables or the Buell ones? I doubt the Buell/Domino ones will fit the Kawi throttle switch housing as they are completely different designs.
If we need to use Kawi throttle cables, which application? Having the cables too long or too short isnt going to fly, unless you can re-route them to accomodate.

When I swapped the bar on my V-rod, I had to source new cables as the old ones were now too long, and there wasnt enough room to re-route them to make up for the length. I was hoping the narrow, higher rise bar (stock) bar could use the same cables as the wider, low rise (stock) bar, but noooooooo!!!!
 
So, looking at a Versys (I think its a 2014), here is what the throttle side looks like. Maybe the Kawi control is made by Domino? There is no way the Kawi cable would work in the Buell as is it waaaaay too long!

This is from the riders perspective looking under the handlebar. The other wire loom is from the heated grips installed on this bike.

v1.jpg

This is from the front looking under the bar, and that actually looks a lot like the Buell/Domino cable. Hmmm...
If you click on the photo it revert to the correct orientation.

v2.jpg
 
So here is what the cables from the parts diagram at Revzilla looks like. Maybe the Buell cables will fit the Kawi housing.


v3.jpg


Damn you CoOter!


You'd better be right, because I just bought a Kawasaki Versys control.
 
Last edited:
The only part I bought was the switch housing, and the only part I modified was the Kawi plug, to match the Buell harness. Same circuits, different plug.

You are right though. I did try to explain the same thing several ways and I could get confusing. I should have put 'THIS goes THERE', even though it doesn't matter, it's easier to follow. Maybe I'll just show up to the brightest garage in the complex and help you drain your beer fridge. I mean, work on the bike...
 
I have an extra set of throttle cables and I'll take some pics of the installation of the cables into the switch housing, after I receive mine. Your documentation of the rewiring of the switches was spot on.

I agree that the Kawi switch feels much better than the Buell switches. My 2004 Ducati uses Domino switches as well, and even they feel much better than the stock XB ones. In fact, the Ducati utilized the LH manual "choke" that Buell switch sort of deletes.
 
Last edited:
:up: I have both EBR switches and I did the EBR 1190 MotionPro Rev2, it works not perfect where it 90° on to the throttle body but it's still going strong

aBXmAq7.jpeg


2C8kRSq.jpeg
 
Back
Top