• You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will see less advertisements, have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

    If you have any problems with the registration process or your account login, please contact us.

Search results

Buellxb Forum

Help Support Buellxb Forum:

  1. R

    WTB xb12r pipes

    Does anyone have a header pipe for a 2005 xb12r motor in good condition they would to sell?
  2. R

    12 run hotter than a 9?

    Hey Buellers,just finished the swap of putting in a 05' xb12r motor into my 03' xb9r,also did the primary gear swap of the 9's into the 12,on Saturday had a 3 hour Dyno tune session at JTnS Performance here in Sonoma,the end result is a total torque monster that eats inline fours,question is do...
  3. R

    ECM question

    Great learning process, if your interested, on the xb9r wiring harness, all electrical demands for the bike are connected, the xb12r and xb9r use 98% of the same parts, the terminal between the 2 ECM plugs is not a electrical item used on my xb9r, doing this swap, it will not be an issue
  4. R

    ECM question

    No, the ECM that I put on is for the 2005 xb12r motor that I also just put in, the ECM is from or came with the xb12r motor that is now in my xb9r frame, just wondering if that middle prong in will affect anything since my it will not be connected
  5. R

    ECM question

    So I put the ECM from the xb12 on xb9, I noticed that the ECM on the 12 has a plug inbetween the two main plug ins and my 9 didn't, is that something on the 12's only and will this affect anything since I am now running a xb12r in my xb9r frame and wiring harness? Thank you in advance;)
  6. R

    Sprocket/chain compatibility question

    Got it done, very tight tolerances, you must have the chain, from the 9, on the front sprocket and the rear and slide them both on at the same time, not the easiest, but doable, then set proper chain tension, looking forward to ripping it up with this thing:D
  7. R

    Sprocket/chain compatibility question

    Doing the xb9 primary gear swap into the xb12 and my primary chain form my xb9 is to short and the primary chain from the xb12 seems to long[confused] the xb9 primary gear and chain are from a 2003 xb9r and going into a 2005 xb12r motor, is my 03 chain not compateable with the 05 clutch/tranny...
  8. R

    Cam gear help?

    Once again, thank you Terry over at JT&S PERFORMANCE, here in Sonoma County, he took time out of his busy day( its a race weekend ) to talk me through everything over the phone,Terry, YOU DA MAN[up] If anyone on here needs any advise on there Buell, these are the guys to call;)
  9. R

    Cam gear help?

    Good morning ,I'm in the process of swapping a 1203 into my xb9r frame, getting to the point, the cam gearcase cover was cracked on the 12 so I went to take off the cover to put my 9's on, while pulling off the cover, the rear cam came with it, no biggie, but I don't have my 12 manual yet, would...
  10. R

    Rear transmission sprocket

    Right on Kona,and Yes,im talking about the rear output shaft pulley that conects the belt to the rear sprocket,thank you on the info;)
  11. R

    Rear transmission sprocket

    Fock,did you do anything to lock the sprocket up,like the belt being on,although you did say you were tearing appart your motor, i just dont want to break anything in the tranny,and thanks for the input
  12. R

    DEI "Titanium" vs Fiberglass exhaust wraps

    Good info kd4gru,just did my pipes with the black Dei wrap tonight,i have hi temp silicone spray and will coat them well,thanks for saving me from losing it;)
  13. R

    Rear transmission sprocket

    Ok,so I have to remove the rear tranny sprocket,the manual tells of a "holding tool"don't have one,has anyone just taken the sprocket off with an air impact? And anyone know the size of the sprocket nut? I am aquiring all the one off sized impact sockets doing my swap,at least I'll have them...
  14. R

    9S subframe trade for R subframe

    some of the older members on here will remember back when mountainclimber and I did this swap,we were among some of the first,everyone thought it looked stupid,now it is a desired swap,they look great and add a different look to the bike,someone will jump on it
  15. R

    buell factory right side scoop

    Just ordered my right side air scoop kit from the HD dealer,some of the prices in these posts,some dates 2009, have changed,the whole kit cost me $100.58 from the dealer,a lot more than listed in earlier posts,but still a decent price when compaired to aftermarket
  16. R

    Rotor assembly question

    Looks like I will call JTnS up here in Sonoma,CA,when they open,I'll post and let you guys know if their compateable;)
  17. R

    High HP Replacement for displacement??

    I would check out www.revolutionperformance.com they have some great big bore kits,have seen their 90ci kit on a xb12,total rocket,all depends on how much your willing to spend,you get what you pay for
  18. R

    Rotor assembly question

    Hey Buellers,I am in the process of putting an xb12r motor into my xb9r bike,I am also doing the primary gear switch on my 9's gear into the 12,since I have the rotor and primary gear from my 9 already in tact,can I just install it as a unit into the 12 or are the rotor assembly housings not...
  19. R

    exhaust mount wear?

    Hey Buellers,in the process of doing a swap of a xb12r motor into my xb9r,came across this,has anyone else had this kind of wearing on your exhaust mount,I know it's from the oil lines rubbing against it from motor vibrations,what can be done to get rid of this or what have you done? Would hate...
  20. R

    Parting Out 2007 Buell Lighting XB12S

    Interested in your ecm if you still have it;)
Back
Top