ECM Spy

[RDuncan]

Is there a version for an Evo4G?

 

[MotoX6]

sidefx, i have maps you might want. so does buell mods but i made one too that i run on my 03 xb9.

SnyderJ21, I think the ecm on the 09 is self learning. I believe you install your mods then ride it for about 10 minutes at around 3000-3500 rpms with no sudden revs or power increases. i would do a tps reset too. i have maps for the 9 if you want them though.

correct me if im wrong!

 

[MotoX6]

eaturwheaties09, post your email address and ill pm you the link.

 

[mflueras]

I'm also looking for an older version of ecmspy. I had it on my old laptop but it crashed and I just found out the price for the registered version. Ykes...

Anyways, can please someone point me in the right direction, link, e-mail with program, whatever. I need to do a TPS reset for my 03. My email is [email protected].

 

[MotoPhreke]

http://mods.buellxb.com/
Has the older version of ECMSpy available for download..

 

[mflueras]

Awesome....got it.

 

[Savis007]

Hi all I have just brought a 2005 XB12R with a race exhaust and ECM. I have just downloaded ECMspy and will make a cable once I find an appropriate post showing how to (HINT for some help please)Could anyone please send me maps that I can play around with to see what works best for the beast.
cheers

 

[tunerbuilder]

hey folks. I have a 05 xb12r with a cut airbox, K&N filter, breather re-route with catchcan, Drummer ss, and factory scoops/body etc. the bike came with a tfi on it however I hate the tfi. (no servo delete, no real tune = super junk). Im really in need of a starting point for the tune on this bike as once the tfi is gone it will be a stock ecu with tons of leaning mods. If anybody can chime in with a map for a similar bike I would be super super appreciative.
I now have my cable, ecmspy, megalog viewer, Tunerstudio with ve analyze, and everything is registered. at this point I will begin saving the stock tune and resetting the tps and removing the servo. but after that... well HELP! THANKS

 

[ah555666]

I'm in need of the ecmspy program and maps if anyone can help. I have a 06' Xb12ss with k&n filter, I think a drummer pipe, its short and black with dual 2" outlets and loud. Not a race can though. Bike runs but needs more fuel. Thanks for any help.

 

[ah555666]

Any chance I can get the ecmspy program sent to my e-mail? This is my 3rd Buell. I am trying to get it to run better and need the program to do a tps reset. I have tried the buellmods link and haven;t had any luck. I am not even sure which I need to download. Thanks for any support. [email protected]

 

[Buellysses]

http://www.buellxb.com/Buell-XB-Forum/Do-It-Yourself-Buell-Mods/ECM-Spy-Download

 

[roofchop]

Help needed in Australia!
I have a 2008/9 XB12ss, It had been dropped and has multiple faults (about 15!)
I got ECMSPY hooked it up and it communicates with the bike ok, I can move the tacho and turn on the fuel pump etc, but when I try to reset faults it says Firmware not found!
What am I doing wrong?
Do I need a different download?
If so which one and where from for free preferably!
Thanks in advance
Dave
email to [email protected]

 

[roofchop]

Bump!
Can anyone help, I really do not want to go to the dealer when I am so close to sorting this myself....with your help!
Firmware not found! what do I need to do?
Thanks
Dave[confused]

 

[Buellysses]

What version of ECM Spy are you using? What buttons are you pushing to do the reset or the trouble codes? What are the error codes it is giving you?

 

[roofchop]

Thanks Buellysses,
V1.12.27
I run Diagnostic functions one by one then go to trouble codes tab,
current codes are
Byte 1.8 bit 7 trouble code 36 fan short or open
Byte 2.0
Byte 3.0
Byte 4.0
Byte 5.0
When I hit read
I get failed to get firmware version
Clear says toggle ign to finish
I will check out the fan now.

before I got the cable and ecmspy I shorted the pins and counted the flashes, That is when I got many faults (can't remember them now)
Thanks again in advance!

Dave

 

[roofchop]

Bump.....
I am desperate and don't want to go to a dealer!
I am so close, just need to reset the ecu?
BTW bike is cranking but not firing, ignition is all good as it dose a 2 second "burn" to the plugs when turned on.
Thanks
Dave

 

[roofchop]

Dose anyone know how get the correct firmware for an 08 xb12ss?
Please help I have spent hours searching to no avail.
[confused]
Dave

 

[amon2001]

Brandnew to Buell and this site...
Wondering if anyone has the maps for a 2009 xb12ss with a jardine exhaust as the only mod...
or any suggestions...

 

[Hooker]

i have a 2003 Buell XB9S with a K&N filter and D&D pipe. anyone have a good tune for a similar bike?

 

[klink]

Has anyone experience the ECMSPY tacho not responding on the overview tab. Everything else works a treat.