LED Turn Signals which to get?

[bardo688]

I need to get some new signals for christmas because two of mine are cracked...any one have suggestions of some they really liked and didnt require lots of fitting?
Has anyone tried these from ebay? item number 230535293495

 

[Miami78]

I have those exact ones, like them a lot...here they are in action:

 

[Nooner]

If you don't mind dropping some coin, the Oberon signals and bar-end signals are awesome.

 

[anrkizm95]

[up][up][up] on the oberon

 

[50dro]

If you don't mind dropping some coin, the Oberon signals and bar-end signals are awesome.

+1 on that. I just installed a set of these with the mirror attachment on my friend's CR. Very nice parts!

 

[Miami78]

Agreed, I have the oberon flashers up front, very nice quality. Would have liked to do the flashers on the bar ends if I didn't have their bar end mirrors there!

 

[50dro]

You can see them here. Good stuff! [up]

 

[bardo688]

Nah Iam in highschool cant afford much
Thanks Miami where those quick and easy to install?

 

[50dro]

LED Signals

In that case, I picked up a set like these from Cycle Gear for $30. EBay would be cheaper. They were easy to install but make sure you get the LED flasher.

 

[xtremelow]

I would shoot for these, they have an Aluminum Body versus a cheaper plastic and look like a sister set that cost $50

LED Turn Signals

Look like these $50 signals, I had but lost in a crash.

 

[Banzai]

I have some like xtremelow, but I got mine from American Sportbike.

http://www.americansportbike.com/shoponline/ccp0-prodshow/16117.html

I also have an integrated rear, but I got that off ebay.

Running LED's on both ends, the best flash rate was from using the resistors that came with the rear. I also have a LED flasher module from ASB, and it didn't slow things down enough by it's self, and with the resistors, they didn't flash, just steady on.

I wrapped the resistors in header wrap and zip tied them to the sub frame under the rear plastic.


Also, holy crap, those bar end signals are PIMP. I like having my Throttle Meister too much though.

 

[delta one]

try here D2 Moto

 

[xtremelow]

@Banzai, I also got mine off ASB and the Integrated LED off ebay for the rear. Love the setup, but not sure what my next setup will be with my new bike build.

 

[Banzai]

@xtreme Those bar end signals look pretty cool.

The Integrated rear makes so much difference in the way the back of the bike looks. Especially after you remount the plate and take off the passenger pegs.

It looks like a whole different bike.

 

[Miami78]

Bardo - the bayonet plugs that come on the are too small for our fittings, had to get a pack from radio shack for a dollar or two and switch them out, otherwise very easy to install.

 

[bardo688]

@extremelow - Did you have to get a ristor for those or where they just bolt on?
Iam looking at just unhooking mine and screwing new LED's on I dont wanna buy a bunch of extra's I just want a set of great front and rear flashers

 

[50dro]

If your bike doesn't have LED's now, then that is impossible. You need either the in-line resistors or an updated LED flasher ($12 at Pep Boys and one minute to install). I'd recommend the LED flasher personally.

 

[williegoat]

 

[zrex]

I got the Rizoma Zero 11's, I got the black ones for my XB12R and the silver ones for my ZRX1100. They're good quality and very bright http://www.pjsparts.com/catalog/product_info.php?cPath=59&products_id=642

 

[bardo688]

Get an "LED flasher" and install that along with my new LED blinkers and toss the stock 4