buell factory right side scoop

[rodie81]

Question for you...

Is anyone running the new factory ecm map that accompanies the "Rider Comfort Kit"? If so, what are your impressions beyond changes in fan operation?

Thanks for any input!

 

[baileycao]

I like the ecm changes. I cant really feel a whole lot of difference other places other than the fact the butt and inner leg does not get hot anymore. Overall the ride heat has gone done a whole lot.

 

[wavex]

tseldon: read previous pages in this thread, there are pics all over the place...

baileycao: just drop by a Harley dealer and ask them for the "Rider Comfort Kit" ecm map? Do they flash for free?

Thanks

 

[jet6]

Anyone?

Who would be willing to buy one of these kits and post it to Australia for me? Ill be paying of course!

Matt

 

[baileycao]

tseldon: read previous pages in this thread, there are pics all over the place...

baileycao: just drop by a Harley dealer and ask them for the "Rider Comfort Kit" ecm map? Do they flash for free?

Thanks

I had them do mine when they did my first service and they didnt charge for it on the receipt. I would assume that it would be free if you just took the bike in. And just tell them it came with the riders comfort kit.

 

[wavex]

Thank you!

 

[Ronin1]

Just completed mine. The fan never even came on after a 20 minute ride.

[/img]

[/img]

[/img]

[/img]

[/img]

Jim T.

 

[Baal]

My results are the same as Ronin1's. Except that it was about a 100 mile ride, and the fan only came on when I stopped and turned the bike off. It was about 67 degrees out, and when I'd ridden it at that temperature before, the fan was pretty much FT. If you're debating about this mod, I highly recommend it.

 

[NOMADIC]

how well do they match? left and right...does one extend farther than the other? and are they horizontally even when looking dead on.. Im just not sure what to make of some of these pics..

 

[NOMADIC]

and also will it fit on an 06 9sx? I think the header is aligned/shaped differently than an 08? Any help would be great guys! [confused]

 

[jet6]

Anyone?

 

[Ronin1]

They match as well as can be expected considering that the engine is asymmetrical. They look even when you are on the bike.

Jim T

 

[AusXB12ss]

Jet6

I'm in brisbane and just ordered one from morgan and wacker so you should be able to get it from any dealer $47 outer $39 inner $8 for screws
all in AUD of course

 

[ausxb]

What seat is that Ronin1 in your pics shown?

 

[dave_xb12r]

Looks like a Corbin

 

[jet6]

Sweet as AusXB12ss, thats cheap, but im 4 hours from any HD/Buell dealer, and this is my issue

Better call Pete and see if hes reading this thread, Pete you there? i want!!!!!!

 

[Ronin1]

Ausxb,
It indeed is a Corbin as Dave noticed. Worlds better comfort than the stocker. It's about an inch taller than the SCG seat but I'm ok with that even with my short-ass inseam. It eased my knee angle a bit also. I'd rather have comfort while riding than stopped since thats where I spend most of my time!

On a side note Juice and I went out yesterday riding, and while not really an apples to apples comparison his fan always ran longer than mine at any stop. He has not done the right scoop yet.

Jim

 

[mmcc100]

Ronin, where did you get the heat shield for your headers? Fit a 2009 XB9?

 

[Ronin1]

MMCC, here on American Sportbike, I think it will fit fine.

http://www.americansportbike.com/shoponline/ccp0-prodshow/17362.html

Jim T.

 

[Guiness63]

I have an 09SS. Do I need the whole comfort kit? I've heard that the the underseat shield won't fit the XBSS's? Also, does the kit come with the header shield?